JANOME Hello Kitty 13512 Instruction Booklet

8vnmWinding the Bobbinz Pull the handwheel out.x Draw the thread from the spool. Guide the thread around the bobbin winder thread guide.c Ins

9zcxzxcvbvbThreading the MachineRaise the take-up lever to its highest position by turning the handwheel toward you.Raise the presser foot.Place a spo

10qerwtyThread Tension Dial• Correcttension The thread tension is adjusted depending on the sewing materials, layers of fabric and sewing meth

11qStitch Selector DialTurn the stitch selector dial to set the setting mark with the symbol corresponding to the desired pattern. q Setting mark

12Reverse Stitch ButtonAs long as you keep the reverse stitch button depressed, the machine will sew in reverse.Darning PlatePosition the darning plat

13w eqq Pattern selector: A or Bw Presser foot: Zigzag foote Thread tension: 2–6r Stitch length: 1.5–4SECTION III. BASIC SEWINGStraight Sti

14q q Center needle position w Guide lines e NumbersSeam Guide LinesThe numbers on the needle plate indicate the distance between the center need

15Tricot Stitchq Pattern selector: Dw Presser foot: Zigzag foote Thread tension: 1–4r Stitch length: 0.5–4This stitch is used to finish the raw e

16This strong, durable stitch is recommended where both elasticity and strength are necessary to ensure comfort and durability. Use it to reinforce ar

17q Pattern selector: Cw Presser foot: Zigzag foote Thread tension: 3–7r Stitch length: Anyt Darning plateSewing ButtonsAttach the darning plate

IMPORTANT SAFETY INSTRUCTIONSWhen using an electrical appliance, basic safety precautions should always be followed, including thefollowing:This sewin

18(A)(B)(C)z Carefully mark buttonhole length on fabric. Place the fabric under the foot with the buttonhole marking running toward you.x Move

19Zipper Applicationq Pattern selector: Aw Presser foot: Zipper foote Thread tension: 2–6r Stitch length: 1.5-4Pin or baste zipper tape to fabri

20q werqSmockingq Pattern selector: Dw Presser foot: Zigzag foote Thread tension: 1–4r Stitch length: S.S.With the stitch length at “4”, sew

21Stretch Stitch Patternsq Pattern selector: A-Gw Presser foot: Zigzag foote Thread tension: 1–4r Stitch length: S.S.If forward and reverse

22qweyrtuSECTION VI.TAKING CARE OF YOUR MACHINECleaning the Bobbin Case and the HookDismantling Shuttle Race UnitRaise the needle to its highest posit

23Sewing LightThe sewing light is located behind the face cover.To change the bulb, take the face cover off the sewing machine by removing the setscre

24TroubleshootingCondition Cause ReferenceThe needle thread breaks.The bobbin thread breaks.The needle breaks.Skipped stitchesSeam puckeringThe cloth

JANOME AMERICA, INC.10 Industrial Ave., Suite 2Mahwah, NJ, 07430 USA1-800-631-0183 ext [email protected]© copyright JANOME AMERICA, INC.31

1SECTION I. ESSENTIAL PARTSName of Parts ... 2Extension Table ...

2qwrtyuio!0!1!4!5!7!6SECTION I. ESSENTIAL PARTSName of Partsq Reverse stitch buttonw Pattern selector dial e Stitch length dialr Bobbin winder sto

3wryqqetStandard Accessoriesq Bobbinsw Seam ripper/ Buttonhole openere Needle setr Sliding buttonhole foott Blind hem footy Zipper footu Darning plate

4Operating Instructions (for the U.S.A and Canada only)This appliance has a polarized plug (one blade wider than the other). To reduce the risk of an

5Presser Foot LifterThe presser foot lifter raises and lowers your presser foot.You can raise it about 0.6 cm (1/4˝) higher than the normal up positio

6Fabrics ThreadNeedle SizeCrepe de Chine, Voile, Fine Silk 9Lawn, Organdy, Fine Cotton orGeorgette, Fine Synthetic 11Tricot Fine Cotton Covered

7When inserting the bobbin case, place the horn into the recess of the hook race. e HornSetting Spool PinsThe spool pins are used for holding the spo